Ahci Controller Driver For Microsoft Windows

Download Standard SATA AHCI Controller Drivers Windows 10 It is reported that on Windows 10, there always exists a SATA AHCI controller driver compatibility problem. After updating to Windows 10, your Windows 7 SATA AHCI controller driver can no longer be compatible with Windows 10. Microsoft standard ahci 1.0 serial ata controller drivers for windows download Google on “changing to AHCI mode” for complete instructions. If you are already up to date, it’ll tell you that, too Windows has determined the driver software for your device is up to date.

AHCI
Advanced Host Controller Interface
Website	www.intel.com/content/www/us/en/io/serial-ata/ahci.html

The Advanced Host Controller Interface (AHCI) is a technical standard defined by Intel that specifies the operation of Serial ATA (SATA) host controllers in a non-implementation-specific manner in its motherboard chipsets.

The specification describes a system memory structure for computer hardware vendors to exchange data between host system memory and attached storage devices. AHCI gives software developers and hardware designers a standard method for detecting, configuring, and programming SATA/AHCI adapters. AHCI is separate from the SATA 3 Gbit/s standard, although it exposes SATA's advanced capabilities (such as hot swapping and native command queuing) such that host systems can utilize them.

As of March 2014, the current version of the specification is 1.3.1.

2Operating System Support

Operating Modes[edit]

Many SATA controllers offer selectable modes of operation: legacy Parallel ATA emulation (more commonly called IDE Mode), standard AHCI mode (also known as Native Mode), or vendor-specific RAID (which generally enables AHCI in order to take advantage of its capabilities). Intel recommends choosing RAID mode on their motherboards (which also enables AHCI) rather than AHCI/SATA mode for maximum flexibility.^[1] Legacy mode is a software backward-compatibility mechanism intended to allow the SATA controller to run in legacy operating systems which are not SATA-aware or where a driver does not exist to make the operating system SATA-aware.

When a SATA controller is configured to operate in Legacy Mode, the number of storage devices per controller is usually limited to four (two IDE channels, primary and secondary, with up to two devices per channel), compared to the maximum of 32 devices/ports when configured in AHCI mode.^[2]^[3]

Operating System Support[edit]

AHCI is supported out of the box on Windows Vista and later, Linux-based operating systems (since version 2.6.19 of the kernel), OpenBSD (since version 4.1), NetBSD (since version 4.0), FreeBSD (since version 8.0), macOS, eComStation (since version 2.1), and Solaris 10 (since version 8/07).^[4]DragonFlyBSD based its AHCI implementation on OpenBSD's and added extended features such as port multiplier support. Older versions of operating systems require hardware-specific drivers in order to support AHCI. Windows XP and older do not provide AHCI support out of the box.

System Drive Boot Issues[edit]

Some operating systems, notably Windows Vista, Windows 7, Windows 8, Windows 8.1 and Windows 10, do not configure themselves to load the AHCI driver upon boot if the SATA controller was not in AHCI mode at the time the operating system was installed. Although this is an easily rectifiable condition, it remains an ongoing issue with the AHCI standard.

The most prevalent symptom for an operating system (or systems) that are installed in IDE mode (in some BIOS firmware implementations otherwise called 'Combined IDE mode'), is that the system drive typically fails to boot, with an ensuing error message, if the SATA controller (in BIOS) is inadvertently switched to AHCI mode after OS installation. In Microsoft Windows the symptom is a boot loop which begins with a Blue Screen error, if not rectified - and through no fault of the Windows OS.

Technically speaking, this is an implementation bug with AHCI that can be avoided, but it has not been fixed yet. As an interim resolution, Intel recommends changing the drive controller to AHCI or RAID before installing an operating system.^[1] (It may also be necessary to load chipset-specific AHCI or RAID drivers at installation time, for example from a USB flash drive).

On Windows Vista and Windows 7, this can be fixed by configuring the msahci device driver to start at boot time (rather than on-demand). Setting non-AHCI mode (i.e. IDE or Combined mode) in the BIOS will allow the user to boot into Windows, and thereby the required registry change can be performed. Consequently, the user then has the option of continuing to use the system in Combined mode or switching to AHCI mode.^[5]With Windows 10, this can be fixed by forcing the correct drivers to reload during Safe Mode.^[6]

In Windows 8, Windows 8.1 and Windows Server 2012, the name of the controller has changed from msahci to storahci,^[7] and the procedures to upgrade to the new controller is similar to that of Windows 7.^[8] On Windows 8, 8.1 and Windows Server 2012, changing from SATA mode to AHCI mode without first updating the registry will make the boot drive inaccessible (i.e. resulting in a recurring boot loop, which begins with a Blue Screen error).

Ahci Controller Driver For Microsoft Windows

A similar problem can occur on Linux systems if the AHCI driver is compiled as a kernel module rather than built into the kernel image, as it may not be included in the initrd (initial RAM disk) created when the controller is configured to run in Legacy Mode. The solution is either to build a new initrd containing the AHCI module, or to build the AHCI driver into the kernel image.^[9]

Intel Ahci Driver Windows 10

Power management[edit]

Power management is handled by the Aggressive Link Power Management (ALPM) protocol.

References[edit]

^ ^a^b'Intel Matrix Storage Technology - Changing and/or choosing Serial ATA Modes'. Intel. Retrieved 2007-09-30.
^'PCI IDE Controller Specification 1.0'(PDF). Berg Software Design. Retrieved 2015-05-03.
^'Serial ATA AHCI: Specification, Rev. 1.3.1'. Intel Corp. Retrieved 2015-05-03.
^'What's New in the Solaris 10 8/07 Release - Driver Enhancements'. Oracle. Retrieved 2010-10-20.^{[permanent dead link]}
^'Error Message when you start a Windows 7 or Windows Vista-based computer after you change the SATA mode of the boot drive: 'STOP 0x0000007B INACCESSABLE_BOOT_DEVICE''. Microsoft. Archived from the original on 24 May 2011. Retrieved 2011-04-20.
^'Enabling AHCI mode AFTER Windows 10 installation'. tenforums.com user Toobad. Retrieved 2015-12-19.
^'StorAHCI replaces MSAHCI (Windows)'. Microsoft.
^'Improving performance of SATA drives on Windows 2012'.
^'Support | How to enable AHCI support after install'. Novell.com. Retrieved 2014-05-11.

External links[edit]